NewNew: GlanceDesk Compute, checked engineering calculators for civil, electrical and HVAC work. See what comes next.
GlanceDeskCompute

Ask an engineering tool

Try:

Answers come from the same tested tools. Nothing you type leaves your device.

Radio Link Budget and Fresnel Zone Calculator

dBm

The numbers filled in are examples. Type your own.

dB
dBi
dBi
dB
dB
Losses beyond free space that you have estimated, such as rain, gases, obstacles or polarisation mismatch. Enter 0 for free space only.
dBm
From the radio datasheet, for the data rate you will use.
In the same unit as the path length, for example where a building or hill stands. The middle of the path has the widest zone.
How far the straight line between the antennas passes above the obstacle top. Negative if the obstacle reaches above the line.

Enter the transmitter power, cable losses, antenna gains, path length, frequency and receiver sensitivity. See the received power and the fade margin, with free-space loss from ITU-R P.525, and the first Fresnel zone radius at a point you choose (ITU-R P.526).

Results are estimates for planning and learning. This is not a licensed link design or a regulatory compliance check: transmitter power, EIRP and frequency use are set by each country's radio regulations, so check your national regulator's rules. A real path also needs Earth curvature, terrain, rain and fading studied.

Received power
–
Fade margin above the receiver sensitivity
–
Free-space path loss
–
EIRP
–
First Fresnel zone radius at the point (m)
–
First Fresnel zone radius at the point (ft)
–
Clearance as a share of the first Fresnel zone radius
–

Assumptions

  • Free-space loss from ITU-R P.525 equation (6); every other path loss is the single figure you enter.
  • Antenna gains are in dBi, towards each other; cable losses are between each radio and its antenna.
  • The Fresnel radius uses ITU-R P.526 equation (3), a good approximation when the path is much longer than the wavelength.
  • Clearance is the height you measured or estimated; Earth curvature and the atmosphere's bending are not added.

Estimate Checked 29 October 2026 Recommendation ITU-R P.525-5 (11/2024): Calculation of free-space attenuation, equation (6) All sources

How it is calculated

  • EIRP = Pt − Tx cable loss + Gt (dBm)
  • Free-space loss Lbf = 32.4 + 20 lg f + 20 lg d (dB), f in MHz, d in km (ITU-R P.525-5, eq. 6)
  • Received power Pr = EIRP − Lbf − other losses + Gr − Rx cable loss (dBm) (ITU-R P.341-7, eq. 2 and 3)
  • Fade margin = Pr − receiver sensitivity (dB)
  • First Fresnel zone radius R1 = 550 × √(d1 × d2 ÷ ((d1 + d2) × f)) (m), d1 and d2 in km, f in MHz (ITU-R P.526-16, eq. 3)
  • Clearance share = clearance ÷ R1 × 100%; 1 mi = 1.609344 km, 1 ft = 0.3048 m

Worked example

A 10 km, 5.8 GHz point-to-point link with 24 dBi dishes, and a roof 4 m below the line of sight halfway along.

You enter
Transmitter output power20 dBm
Transmitter cable and connector loss1 dB
Transmitting antenna gain24 dBi
Path length10
Distance unitKilometres (km)
Frequency5.8
Frequency unitGigahertz (GHz)
Receiving antenna gain24 dBi
Receiver cable and connector loss1 dB
Other losses0 dB
Receiver sensitivity-80 dBm
Distance from the transmitter to the point to check5
Clearance at that point4
Clearance unitMetres (m)
You get
Received power-61.67 dBm
Fade margin above the receiver sensitivity18.33 dB
Free-space path loss127.67 dB
EIRP43 dBm
First Fresnel zone radius at the point (m)11.42 m
First Fresnel zone radius at the point (ft)37.46 ft
Clearance as a share of the first Fresnel zone radius35.0%

The transmitter sends an EIRP of 43 dBm. Free space takes 127.67 dB, so about -61.67 dBm reaches the receiver, 18.33 dB above its sensitivity. At the point you chose the first Fresnel zone has a radius of 11.42 m (37.46 ft), and your clearance is 35% of that radius.

Questions

What is a good fade margin?

It depends on the frequency, the path, the climate and how much outage the link can accept, so this tool does not set a target. ITU-R P.530 gives the methods radio engineers use to predict fading for a given availability.

What is the first Fresnel zone?

The football-shaped space around the straight line between two antennas where most of the signal energy travels. ITU-R P.526 explains that a path behaves like line of sight, with little diffraction, when no obstacle enters the first Fresnel ellipsoid.

Why can received power be above the sensitivity and the link still fail?

Rain, multipath fading, interference and obstacles inside the Fresnel zone can take away more than the losses you entered. The margin is what you have in hand to cover them.

Sources and checks

Last checked: 29 October 2026. This tool passes 6 automatic tests before every release. How we check our tools

Cite this page

Radio Link Budget and Fresnel Zone Calculator. GlanceDesk Compute. Last checked 29 October 2026. https://glancedeskcompute.com/radio-link-budget-calculator/

Found a wrong number? Tell us

Your numbers stay on your device unless you share them.

An estimate for planning and learning, not a licensed link design or a regulatory compliance check. A real link needs a path profile, Earth curvature, rain and fading studies, and the frequency and power rules of your national regulator. Results are estimates for planning and learning. They are not a design check and do not replace a qualified engineer or your local building/electrical code.

Related tools

Missing something? Suggest a tool