Fibre Optic Loss Budget Calculator (Fiber Link Power Budget)
Enter the transmitter power, receiver sensitivity, fibre length and attenuation, and the number of connectors and splices with their losses. See the total loss with your safety margin, the power budget, what is left over, and the longest fibre the budget allows.
Results are estimates for planning and learning, from the losses you type in (take them from the cable, connector and transceiver datasheets). This is not an acceptance test or a compliance check; measure the installed link with an optical power meter or OTDR.
- Power left over after all losses and your margin
- –
- Power budget (transmitter power − receiver sensitivity)
- –
- Total loss including your margin
- –
- Fibre loss
- –
- Longest fibre this budget allows (km)
- –
- Longest fibre this budget allows (mi)
- –
Assumptions
- Every loss is the figure you type, from datasheets; the tool adds them in decibels.
- Attenuation is per kilometre at your operating wavelength; a length in miles is converted (1 mi = 1.609344 km).
- The power budget only covers loss. Dispersion and bandwidth limits are not checked.
- The safety margin is your own choice; it is counted as a loss.
Estimate Checked 29 October 2026 Brunel University London, EE5514 lesson 5: Digital transmission system, link power budget (PT = PS − PR = connector losses + αf L + system margin; its examples 1 and 2 are tests here) All sources
How it is calculated
- Power budget = transmitter power (dBm) − receiver sensitivity (dBm)
- Fibre loss = length (km) × attenuation (dB/km)
- Total loss = fibre loss + connectors × loss each + splices × loss each + other losses + safety margin
- Left over = power budget − total loss
- Longest fibre = (power budget − connector, splice and other losses − margin) ÷ attenuation
Worked example
A 20 km single-mode link with a 0 dBm transmitter, a −28 dBm receiver, two connector pairs and four splices.
| You enter | |
|---|---|
| Transmitter output power | 0 dBm |
| Receiver sensitivity | -28 dBm |
| Fibre length | 20 |
| Length unit | Kilometres (km) |
| Fibre attenuation | 0.35 dB/km |
| Number of connector pairs | 2 |
| Loss per connector pair | 0.5 dB |
| Number of splices | 4 |
| Loss per splice | 0.1 dB |
| Other fixed losses | 0 dB |
| Safety margin you want to keep | 3 dB |
| You get | |
| Power left over after all losses and your margin | 16.6 dB |
| Power budget (transmitter power − receiver sensitivity) | 28 dB |
| Total loss including your margin | 11.4 dB |
| Fibre loss | 7 dB |
| Longest fibre this budget allows (km) | 67.43 km |
| Longest fibre this budget allows (mi) | 41.9 mi |
The power budget is 28 dB and the losses with your margin add up to 11.4 dB, of which the fibre itself is 7 dB. That leaves 16.6 dB to spare. At this attenuation the budget would reach about 67.43 km (41.9 mi) of fibre.
Questions
Where do I find the attenuation and connector losses?
On the datasheets for your cable, connectors and splices, at the wavelength you use. The tool has no built-in values, so the answer is only as good as the figures you enter.
Why keep a safety margin?
Connectors get dirty, cables are repaired with extra splices and parts age. The Brunel lecture's example keeps 6 dB; choose what your network needs.
Sources and checks
- Brunel University London, EE5514 lesson 5: Digital transmission system, link power budget (PT = PS − PR = connector losses + αf L + system margin; its examples 1 and 2 are tests here)
- NIST SP 811 (2008), Appendix B: mile = 1.609344 km
Last checked: 29 October 2026. This tool passes 7 automatic tests before every release. How we check our tools
Cite this page
Fibre Optic Loss Budget Calculator (Fiber Link Power Budget). GlanceDesk Compute. Last checked 29 October 2026. https://glancedeskcompute.com/
Your numbers stay on your device unless you share them.
An estimate for planning and learning from the losses you enter. It is not an acceptance test or a compliance check; test the installed link and follow the equipment maker's and your network operator's requirements. Results are estimates for planning and learning. They are not a design check and do not replace a qualified engineer or your local building/electrical code.