NewNew: GlanceDesk Compute, checked engineering calculators for civil, electrical and HVAC work. See what comes next.
GlanceDeskCompute

Ask an engineering tool

Try:

Answers come from the same tested tools. Nothing you type leaves your device.

Decibel Converter: dB, dBm, dBW, Watts and EIRP

A transmitter output or any other power level, in the unit chosen below.

The numbers filled in are examples. Type your own.

dB
Used for the EIRP only. Enter 0 if the transmitter feeds the antenna directly.
dBi
Used for the EIRP only: the gain relative to an isotropic antenna (dBi), from the antenna datasheet.
A separate conversion: a value in dB, or a ratio, as chosen below. A loss in dB is negative.

Two conversions on one page. Enter a power in mW, W, dBm or dBW to see it in every unit, and the EIRP after cable loss and antenna gain. Enter a gain or loss in dB, or as a power or voltage ratio, to see it the other ways.

Results are for planning and learning. This is not a licensed radio-link design or a regulatory compliance check: the transmitter power and EIRP allowed depend on the band and on each country's radio regulations, so check your national regulator's rules.

EIRP (equivalent isotropically radiated power)
–
EIRP
–
Power (dBm)
–
Power (dBW)
–
Power (mW)
–
Power (W)
–
Gain or loss (dB)
–
Power ratio (P1 ÷ P2)
–
Voltage or current ratio (U1 ÷ U2)
–
Gain or loss (Np)
–

Assumptions

  • Powers are real (active) powers; dBm is relative to 1 mW and dBW to 1 W.
  • A voltage or current ratio converts with 20 lg only when both impedances are equal (ITU-R V.574).
  • EIRP uses the antenna gain in dBi, in the direction you care about, and the loss between transmitter and antenna.
  • One neper is 20 lg e ≈ 8.686 dB, the telecommunications definition in ITU-R V.574.

Checked 29 October 2026 Recommendation ITU-R V.574-5 (08/2015): Use of the decibel and the neper in telecommunications (dB, dBm, dBW, dBi, neper; its 15 dB(1 W) example is a test here) All sources

How it is calculated

  • Power level: dBm = 10 × lg(P ÷ 1 mW); dBW = 10 × lg(P ÷ 1 W) = dBm − 30
  • Power ratio in decibels: dB = 10 × lg(P1 ÷ P2)
  • Voltage or current ratio in decibels (equal impedances): dB = 20 × lg(U1 ÷ U2)
  • Nepers: Np = dB ÷ 8.686 (1 Np = 20 × lg e dB)
  • EIRP (dBm) = transmitter power (dBm) − cable and connector loss (dB) + antenna gain (dBi)

Worked example

A 1 W transmitter feeding a 15 dBi antenna through 2 dB of cable, and what 3 dB means as a ratio.

You enter
Power1
Power unitWatts (W)
Cable and connector loss to the antenna2 dB
Antenna gain15 dBi
Gain or loss to convert3
The gain or loss isIn decibels (dB)
You get
EIRP (equivalent isotropically radiated power)43 dBm
EIRP19.9526 W
Power (dBm)30 dBm
Power (dBW)0 dBW
Power (mW)1,000 mW
Power (W)1 W
Gain or loss (dB)3 dB
Power ratio (P1 ÷ P2)1.995262
Voltage or current ratio (U1 ÷ U2)1.412538
Gain or loss (Np)0.3454 Np

The power is 30 dBm (1 W). After the cable loss and the antenna gain, the EIRP is 43 dBm, about 19.9526 W. Separately, 3 dB is a power ratio of 1.995262 and a voltage ratio of 1.412538.

Questions

What is the difference between dB and dBm?

dB is a ratio between two powers, such as a gain or a loss. dBm is an absolute power level compared with 1 milliwatt: 0 dBm is 1 mW, 30 dBm is 1 W. A loss in dB is subtracted from a level in dBm.

Why is a voltage ratio multiplied by 20 and a power ratio by 10?

Power is proportional to voltage squared in the same impedance, and the logarithm of a square is twice the logarithm. ITU-R V.574 notes this only holds when the impedances are equal.

What EIRP am I allowed to transmit?

That depends on the frequency band, the service and the country. National regulators set the limits under the ITU Radio Regulations, so check your own regulator's rules; this tool does not give limits.

Sources and checks

Last checked: 29 October 2026. This tool passes 9 automatic tests before every release. How we check our tools

Cite this page

Decibel Converter: dB, dBm, dBW, Watts and EIRP. GlanceDesk Compute. Last checked 29 October 2026. https://glancedeskcompute.com/decibel-converter/

Found a wrong number? Tell us

Your numbers stay on your device unless you share them.

For planning and learning. Not a licensed link design or a regulatory compliance check; it does not replace a qualified radio engineer or your national radio regulations. Results are estimates for planning and learning. They are not a design check and do not replace a qualified engineer or your local building/electrical code.

Related tools

Missing something? Suggest a tool