NewNew: GlanceDesk Compute, checked engineering calculators for civil, electrical and HVAC work. See what comes next.
GlanceDeskCompute

Ask an engineering tool

Try:

Answers come from the same tested tools. Nothing you type leaves your device.

Open Channel Flow Calculator (Manning's Equation)

The numbers filled in are examples. Type your own.

Width of the flat bed. Not used for a V-shaped channel.
2 means the side goes 2 across for every 1 up (1V:2H). Not used for a rectangular channel.
Used when you find the flow.
Used when you find the depth: m³/s in metric, ft³/s in imperial.
Drop of the channel bed over its length. Steady, uniform flow is assumed, so the water surface runs parallel to the bed.
Picking a lining fills Manning's n from FHWA HDS-4 Table B.2. You can still change n.
Natural streams have ranges, not one value (FHWA HDS-4 Table B.2; USGS Water-Supply Paper 2339 Table 1: cobble bed 0.030 to 0.050). Pick from the range for your channel and type it here.

Choose the channel shape, its size, the bed slope and Manning's n for the lining. See how much water it carries at a given depth, or how deep it runs for a given flow, with the velocity, in metric and imperial units.

Answer
–
Slope used
–
Flow (m³/s)
–
Flow (L/s)
–
Flow (ft³/s)
–
Water depth (m)
–
Water depth (ft)
–
Mean velocity (m/s)
–
Mean velocity (ft/s)
–
Flow area (m²)
–
Flow area (ft²)
–
Hydraulic radius (m)
–
Hydraulic radius (ft)
–

Assumptions

  • Steady, uniform flow: the depth stays the same along the channel and the water surface is parallel to the bed.
  • One lining and one n value for the whole wetted section; a channel with a flood plain needs to be split.
  • Straight, prismatic channel of the shape and size you enter, with no bends, gates or bridges nearby.
  • Manning's n is the value you choose; results change in proportion to it, so a wrong n gives a wrong flow.
  • Not for very steep channels: FHWA HDS-4 refers them to other methods (Jarrett, 1985).

Estimate Checked 5 November 2026 FHWA HDS-4, Introduction to Highway Hydraulics (FHWA-NHI-08-090), 4.3.1–4.3.2: Manning's equation, trapezoid geometry, Examples 4.1 and 4.2; Appendix B Table B.2 (n values) All sources

How it is calculated

  • Flow area A = B × y + Z × y²; wetted perimeter P = B + 2 × y × √(1 + Z²); hydraulic radius R = A ÷ P
  • Rectangular channel: Z = 0. V-shaped channel: B = 0
  • Mean velocity V = (1 ÷ n) × R^(2/3) × S^(1/2), in metres and seconds
  • Flow Q = V × A
  • Normal depth: the depth y at which Q equals your flow, found by repeated halving
  • Feet are converted exactly (1 ft = 0.3048 m), which is the same as using ≈ 1.486 ÷ n in feet units

Worked example

FHWA HDS-4 Example 4.1: a trapezoidal earth channel, 2 m wide at the bed, sides 1V:2H, 0.5 m deep, slope 0.003, n = 0.02.

You enter
What do you want to find?Flow, from the water depth
Channel shapeTrapezoidal (sloping sides)
UnitsMetric: metres and m³/s
Bottom width2
Side slope (horizontal for 1 vertical)2
Water depth0.5
Slope written asm per m (or ft per ft), e.g. 0.003
Bed slope0.003
Channel liningStraight unlined earth canal in good condition (0.020)
Manning's n0.02
You get
Answer2.056 m³/s
Slope used0.003 m/m = 0.3% = 1 in 333
Flow (m³/s)2.056 m³/s
Flow (L/s)2,056.1 L/s
Flow (ft³/s)72.61 ft³/s
Water depth (m)0.5 m
Water depth (ft)1.64 ft
Mean velocity (m/s)1.371 m/s
Mean velocity (ft/s)4.5 ft/s
Flow area (m²)1.5 m²
Flow area (ft²)16.146 ft²
Hydraulic radius (m)0.3541 m
Hydraulic radius (ft)1.1618 ft

At this depth the channel carries about 2.056 m³/s (2,056 L/s), at a mean velocity of about 1.37 m/s.

Questions

How do I choose Manning's n?

From a published table for the channel's lining. FHWA HDS-4 Table B.2 gives single values for built channels (ordinary concrete lining 0.013) and ranges for natural streams; USGS Water-Supply Paper 2339 explains how to adjust a base value for bends, plants and obstructions. A higher n means a rougher channel, so less flow at the same depth.

What is the normal depth?

The depth at which the water flows steadily down a long, uniform channel, with the pull of gravity balanced by friction. Finding it by hand means trial and error, as in HDS-4 Example 4.2; this tool does the repeats for you.

Why does the imperial answer differ slightly from a textbook?

Books round the feet constant to 1.486 or 1.49. This tool converts feet exactly (1 ft = 0.3048 m), which equals 1.4859. HDS-4 Example 4.1 in feet gives 69.06 ft³/s with 1.49 and a rounded radius; the exact value is 68.78 ft³/s.

Sources and checks

Last checked: 5 November 2026. This tool passes 19 automatic tests before every release. How we check our tools

Cite this page

Open Channel Flow Calculator (Manning's Equation). GlanceDesk Compute. Last checked 5 November 2026. https://glancedeskcompute.com/manning-open-channel-flow-calculator/

Found a wrong number? Tell us

Your numbers stay on your device unless you share them.

This is an estimate for planning and learning: the answer rests on the n value you choose, and real channels are rarely perfectly uniform. For drainage, irrigation or flood work that must not fail, ask a qualified engineer. Results are estimates for planning and learning. They are not a design check and do not replace a qualified engineer or your local building/electrical code.

Related tools

Missing something? Suggest a tool